[. . . ] HP Photosmart C7200 All-in-One series Basics Guide Hewlett-Packard Company notices The information contained in this document is subject to change without notice. Reproduction, adaptation, or translation of this material is prohibited without prior written permission of Hewlett-Packard, except as allowed under copyright laws. The only warranties for HP products and services are set forth in the express warranty statements accompanying such products and services. Nothing herein should be construed as constituting an additional warranty. [. . . ] Open the ink cartridge door by lifting from the front center of the device, until the door locks into place. 3. Squeeze the bottom of the latch below the ink cartridge you want to replace, and then lift the latch. If you are replacing the black ink cartridge, lift the latch on the far left. If you are replacing one of the five color ink cartridges, such as yellow, light cyan (blue), cyan, light magenta (pink), or magenta, lift the appropriate latch in the center area. Replace the ink cartridges 41 Use the HP All-in-One features Chapter 4 Use the HP All-in-One features 1 2 Ink cartridge latch for the black ink cartridge Ink cartridge latches for the color ink cartridges 4. Remove the new ink cartridge from its packaging, and then, holding it by the handle, push the ink cartridge into the empty slot. Match the color and pattern of the ink cartridge to the color and pattern on the print carriage. 6. Close the latch and make sure it is secure. 42 Use the HP All-in-One features 7. Close the ink cartridge door. Clean the HP All-in-One To ensure that your copies and scans remain clear, you might need to clean the glass and lid backing. TIP: You can purchase an HP Cleaning Kit for Inkjet Printers and All-in-Ones (Q6260A) that provides everything needed to safely clean your HP device. For more information, go to: www. shopping. hp. com/accessories-store/printer. Clean the glass Glass that is dirty from fingerprints, smudges, hair, and dust on the main glass surface slows down performance and affects the accuracy of features such as Fit to Page. In addition to the main glass surface, you might also need to clean the small glass strip inside the automatic document feeder. Streaks can occur if the glass strip inside the automatic document feeder is dirty. Clean the glass with a soft cloth or sponge slightly moistened with a nonabrasive glass cleaner. CAUTION: Do not use abrasives, acetone, benzene, or carbon tetrachloride on the glass, since they can damage it. The liquid might seep under the glass and damage the device. Clean the HP All-in-One 43 Use the HP All-in-One features Chapter 4 3. Turn on the HP All-in-One. Use the HP All-in-One features 44 To clean the glass strip inside the automatic document feeder 1. Lift the automatic document feeder mechanism. There is a glass strip under the automatic document feeder mechanism. Clean the glass strip with a soft cloth or sponge slightly moistened with a nonabrasive glass cleaner. CAUTION: Do not use abrasives, acetone, benzene, or carbon tetrachloride on the glass, since they can damage it. Lower the automatic document feeder mechanism, and then close the cover of the automatic document feeder. Turn on the HP All-in-One. Clean the lid backing Minor debris can accumulate on the white document backing located underneath the lid of the HP All-in-One. Use the HP All-in-One features CAUTION: Do not use paper-based wipes, as these might scratch the backing. If further cleaning is needed, repeat the previous steps using isopropyl (rubbing) alcohol, and wipe the backing thoroughly with a damp cloth to remove any residual alcohol. [. . . ] · Turn off the HP All-in-One by pressing the On button located on the device. Do not turn off the device by turning off a power strip or unplugging the power cord from the HP All-in-One. If you improperly turn off the HP All-in-One, the print head assembly might not return to the correct position. · Store ink cartridges at room temperature (15. 6°-26. 6° C or 60°-78° F). [. . . ]